Description
Woodward SPM-D11 8440-1701 / 8440-1706 Synchronizer & Load Share Controller
Product Title
Woodward SPM-D11 (P/N:8440-1706) | Panel Mount Synchronizing & Load Sharing Unit for Generator Paralleling
Product Description
SPM-D11 (8440-1706) is a classic Woodward digital synchronizer and load share controller for synchronous generator paralleling. It is used to automatically match voltage, frequency and phase angle between generator and busbar before closing the breaker. It supports isochronous / droop load sharing for multiple gensets, including real power (kW) and reactive power (kVAR) sharing. It has built-in voltage and frequency regulation outputs to governor and AVR, plus protective logic for out-of-sync blocking. Front LCD and keypad for local viewing and parameter setup; PC software for configuration. Typical variants: SPM-D11/LSR, SPM-D11/LSXR with extended load share capability. Widely used on marine power, island microgrid, industrial multi-generator power station, combined heat & power CHP.
Technical Specifications
| Item | Parameter |
|---|---|
| Brand | Woodward (伍德沃德) |
| Model | SPM-D11, Part No. 8440-1706 |
| Mounting | Panel mount 144×72mm |
| Power Supply | 12/24 VDC (9.5 ~ 32 VDC) |
| Power Consumption | Max 12W |
| Measuring Input | PT:100VAC / 400VAC; CT: 1A or 5A |
| Frequency Range | 40 ~70Hz (50/60Hz) |
| Accuracy | Class 1 |
| Control Output | Analog 0~±10V for governor speed & AVR voltage trim |
| Relay Outputs | Potential-free relay contacts for breaker, alarm, sync-permissive |
| Communication | RS485 Modbus RTU |
| Operating Temperature | -20°C ~ +70°C |
| Storage Temperature | -40°C ~ +85°C |
| Humidity | 5~95% non-condensing |
| Front Protection | IP42 (IP54 with gasket fitted) |
| Certifications | CE, UL/cUL |
| Weight | Approx. 0.8kg |
| Diagnostics | Loss of voltage, phase fault, CT/PT wiring fault, out-of-sync prevention |
Compatibility & Installation Pitfalls
Compatibility
- Genset: Diesel / gas synchronous generators
- Partner controls: Woodward 505/505E governor, easYgen series genset controllers
- Sensors: Voltage transformer PT, Current transformer CT
- Host: PLC / SCADA via Modbus RTU
- Not compatible: Older SPM-D1000 series; it cannot replace easYgen-3500 (8440-1936, all-in-one genset controller)
Critical Installation Pitfalls
- CT secondary safety: CT secondary must be shorted before disconnecting wiring; open CT terminals produce dangerous high voltage.
- Synchronizing window setting: The phase, frequency and voltage window must be correctly configured. Too wide sync window can cause heavy impact damage to generator and bus.
- Load share line wiring (LSR/LSXR): Analog load-sharing bus cable must be shielded twisted pair, dedicated wire, avoid running alongside high-power cables.
- Parameter backup: Save full parameter file via PC software before replacement. Without backup, all sync & load share parameters must be re-programmed.
- DC control power: Use clean battery supply with surge protection. Do not share circuit with engine starter, otherwise voltage dip causes controller reset.
- Panel gasket: Install sealing gasket to maintain front IP rating, prevent cabinet condensation damage.
- Not hot-swappable: Cut DC power and lock out before removal. Live removal loses synchronizing and load share control, risk of generator trip.
Standard Operating Procedure (SOP)
- Pre-Install Inspection & LOTO Lock out generator high voltage and DC control supply. Inspect LCD, keypad and rear terminals, confirm part number 8440-1706. Prepare PC configuration software.
- Panel Mounting Fit into 144×72 panel cutout, install sealing gasket and mounting clips.
- PT/CT & Control Wiring Wire PT voltage, CT current inputs; wire governor / AVR analog trim outputs, breaker relay outputs and RS485 communication. Use shielded twisted pair. Perform insulation & continuity test.
- Controller Configuration Set genset rated parameters, synchronizing window, droop / isochronous mode, kW/kVAR load share parameters, alarm & permissive logic. Save parameter file.
- Power-Up & Commissioning Apply DC control power. Verify voltage, current and frequency readings. Complete dead bus test, no-load synchronizing test and multi-unit load sharing test. Verify out-of-sync blocking protection.
- Runtime Operation & Diagnostics Monitor sync status, load sharing and alarms via front panel or SCADA. Regular backup of configuration file.
- Replacement Procedure Execute LOTO. Short CT secondary first, then disconnect all wiring. Remove old . Install spare 8440-1706, rewire, restore saved parameters and perform full commissioning test.
Application Scenarios
- Multi-generator paralleling in power plants
- Marine vessel power management & shore power synchronization
- Islanded microgrid & peak shaving systems
- Oil & gas site prime power and CHP combined heat & power
- Industrial backup power station with multiple gensets
- Retrofit and spare replacement for legacy Woodward generator parallel control
Supporting Components
- 144×72 panel mounting kit and sealing gasket
- Current transformer CT & voltage transformer PT
- 12/24VDC surge protected battery power supply
- PC configuration software
- Shielded twisted pair for analog load-share and Modbus wiring
- Governor (Woodward 505/505E) and generator AVR
- Circuit breakers and terminal blocks
- PLC/SCADA host for remote monitoring
- Generator breaker interlock logic
- Woodward load-share termination resistors
Related Model Recommendations (10 Models)
- Woodward 8440-1936 easYgen-3500 Genset controller
- Woodward 505 / 505E turbine governor
- Woodward DSLC-2XT 8440-2299 Load share controller
- Woodward DTSC-200A 8440-2297 Synchronizer
- CLS216 Watlow 16-loop temperature controller
- CLS204 Watlow 4-loop temperature controller
- WAGO 758-873 PFC200 PLC
- MCS2000-ECA Warner tension controller
- VM600 MPC4 Vibro-Meter vibration protection card
- IPC704 244-704-000-042-A2-B01-C10 eddy current conditioner



