WATLOW ANAFAZE CLS216 CAS200 | 16-Loop Multi-Point Temperature Controller, CLS200 Series

  1. CLS204: 4-loop version of CLS200 series
  2. CLS208: 8-loop version of CLS200 series
  3. CLS216: 16-loop full model
  4. Watlow F4T: New generation multi-loop controller
  5. Watlow EZ-ZONE PM: Single loop panel controller
  6. Watlow SSR solid state relay
  7. WAGO 758-873 PFC200 PLC (host integration)
  8. MCS2000-ECA Warner tension controller
  9. VM600 MPC4 Vibro-Meter vibration card
  10. IPC704 244-704-000-042-A2-B01-C10 eddy current conditioner
Category: SKU: WATLOW ANAFAZE CLS216 CAS200 Brand:

Description

WATLOW ANAFAZE CLS216 CAS200 | 16-Loop Multi-Point Temperature Controller, CLS200 Series

 

Product Description

CLS216 (CAS200 platform) is Watlow Anafaze high-performance 16 independent loop multi-point temperature controller, belongs to CLS200 compact loop system family. It accepts universal sensor inputs including thermocouple, RTD, mV, mA and voltage signals. It executes PID auto-tune, ramp & soak batch curve control, cascade / ratio / differential control for thermal processes. Equipped with a 32-character VFD vacuum fluorescent display and 8-key front keypad. It supports Modbus RTU, RS232 / RS485 serial communication for SCADA / PLC host connection. It can store up to 8 batch recipes. Digital time-proportional outputs drive solid-state relays or contactors for heating/cooling regulation, widely used for furnaces, thermal treatment, extrusion, oven and semiconductor thermal process control.

 

Technical Specifications

 

Item Parameter
Brand WATLOW ANAFAZE
Model CLS216 (CAS200 / CLS200 series)
Control Loops 16 independent control loops
Input Types Thermocouple, RTD, ±mV, 0/4–20mA, 0–10V
Control Algorithm PID auto-tune, On/Off, Ramp & Soak, cascade, ratio, differential
Display 32-character VFD vacuum fluorescent display
Operation 8-button front keypad
Communication RS232, RS485, Modbus RTU
Recipe Storage Up to 8 batch job recipes
Output Type Time proportional digital output, serial DAC analog retransmit
Power Supply 85–264 VAC universal AC input
Sampling Rate 100ms per channel
Noise Rejection 120dB @ 60Hz
Temperature Coefficient 40 ppm/°C
Operating Temp 0°C ~ +55°C
Storage Temp -20°C ~ +70°C
Humidity 5–95% non-condensing
Mounting 1/8 DIN panel mount
Enclosure Rating Front panel IP65, rear IP20
Certifications CE, UL, C-UL
Weight Approx. 0.75kg
Diagnostics Sensor break, short, overrange, hardware fault

 

Compatibility & Installation Pitfalls

Compatibility

  • Series: CLS200 family (CLS204 / CLS208 / CLS216)
  • Sensors: K, S, B-type thermocouple; Pt100 RTD; 4-20mA / 0-10V transmitters
  • Host system: PLC, SCADA via Modbus RTU / RS485
  • Output loads: SSR solid state relay, contactor, analog recorder
  • Not compatible: CLS100 old generation controllers; single-loop standalone temperature controllers

Critical Installation Pitfalls

  1. Panel cutout requirement: 1/8 DIN panel cutout, ensure gasket is fitted to maintain front IP65 protection against dust and condensate.
  2. Analog sensor wiring: Thermocouple must use compensating cable; analog signals use shielded twisted pair, single-point grounding to avoid ground loop drift.
  3. Ramp-soak recipe backup: Save batch recipes before replacement or firmware update; recipe loss requires re-programming all 16 loops.
  4. PID tuning sequence: Set sensor scaling first, then auto-tune PID one loop at a time. Multiple loops cross-coupling may cause thermal oscillation.
  5. Digital output wiring: Time proportional outputs are low-level logic signals, they cannot directly drive high-power heaters; must connect to SSR or contactor.
  6. Communication bus termination: RS485 Modbus network needs 120Ω terminal resistor at bus two endpoints, otherwise communication error and data loss.
  7. No hot swap: Controller must be powered down before removal. Live removal will stop all 16 temperature loops and cause process over-temperature risk.

 

Standard Operating Procedure (SOP)

  1. Pre-Install Inspection & LOTO Lock-out tag-out AC power and sensor wiring. Inspect front panel, VFD screen and rear terminal block. Confirm model CLS216 CAS200.
  2. Panel Mounting Insert unit into 1/8 DIN panel cutout, fasten mounting clips, install front sealing gasket.
  3. Sensor & Output Wiring Wire thermocouple/RTD/compensating cable to input terminals; connect digital outputs to SSR/contactors. Wire RS485 Modbus communication cable. Perform continuity and insulation test.
  4. Controller Configuration & Recipe Setup Access front keypad or PC configuration software, set sensor type, scale, alarm thresholds, ramp-soak curve, PID parameters. Save batch recipes.
  5. Power-Up & Commissioning Apply AC power. Verify VFD display and sensor readings. Run static test, then slow thermal cycle test to tune PID and validate alarm functions.
  6. Runtime Operation & Diagnostics Monitor 16-loop temperature status via front panel or SCADA. Regularly check sensor fault alarms, backup recipes.
  7. Replacement Procedure Execute LOTO. Disconnect power, sensor and communication cables. Remove old controller. Install spare CLS216, rewire, upload saved recipes, verify all loops.

 

Application Scenarios

  • Industrial furnace & heat treatment multi-zone temperature control
  • Plastic extrusion barrel multi-point heating control
  • Thermal vacuum oven / environmental chamber batch ramp-soak process
  • Semiconductor & packaging thermal processing
  • Food and pharmaceutical thermal sterilization
  • Refinery / chemical reactor multi-point temperature monitoring
  • Retrofit & spare replacement for existing CAS200 / CLS200 thermal control systems

 

Supporting Components

  1. 1/8 DIN panel mounting hardware and sealing gasket
  2. Compensating thermocouple cable / shielded RTD cable
  3. SSR solid state relays for heater drive
  4. 120Ω RS485 bus terminating resistor
  5. Modbus RTU SCADA / PLC host
  6. PC configuration software for CLS200
  7. Temperature sensors: Thermocouple, Pt100 RTD
  8. Circuit breaker for AC power protection
  9. Terminal blocks and cable glands
  10. Spare front membrane keypad

 

Related Model Recommendations (10 Models)

  1. CLS204: 4-loop version of CLS200 series
  2. CLS208: 8-loop version of CLS200 series
  3. CLS216: 16-loop full model
  4. Watlow F4T: New generation multi-loop controller
  5. Watlow EZ-ZONE PM: Single loop panel controller
  6. Watlow SSR solid state relay
  7. WAGO 758-873 PFC200 PLC (host integration)
  8. MCS2000-ECA Warner tension controller
  9. VM600 MPC4 Vibro-Meter vibration card
  10. IPC704 244-704-000-042-A2-B01-C10 eddy current conditioner