Vibro-Meter (Meggitt) VM600 RPS6U 200-582-500 Rack Power Supply Module

  1. CPUM 200-595-100-01: rack CPU
  2. MPC4 200-510-071-113: Vibration protection card
  3. IOC4T 200-560-000-113: Rear I/O communication card
  4. IOC16T 200-565-000-013: 16-channel analog input
  5. IRC4: Relay trip output module
  6. AMC8: Analog measurement module
  7. GSI127 244-127-000-017-A2-B: Galvanic separation unit
  8. XMV16: High density condition monitoring module
  9. IQS9xx: Eddy current signal conditioner
  10. CA-series IEPE accelerometer
Category: SKU: VIBRO-METER-READY Brand:

Description

Vibro-Meter (Meggitt) VM600 RPS6U 200-582-500 Rack Power Supply Module

 

Product Title

Vibro-Meter VM600 RPS6U 200-582-500 | 6U Rack Power Supply for VM600 Machinery Protection & Condition Monitoring System

 

Product Description

The VM600 RPS6U 200-582-500 is the dedicated front-mounted rack power supply unit for Vibro-Meter VM600 ABE04x 6U racks. It converts AC or DC mains input into three regulated DC rails (+5V, +12V, -12V) to power the entire rack including CPUM, MPC4, IOC4T, IOC16T and other VM600 I/O & monitoring modules. The RPS6U supports parallel redundant operation with two units installed in one rack. If one supply fails, the second unit automatically takes over to maintain continuous machinery protection without interruption. It incorporates comprehensive electronic protection including overvoltage, overcurrent, short-circuit and overtemperature protection. Front-panel LED indicators display input power and output rail health. Onboard diagnostics report power status and fault alarms to the CPUM via the rack backplane. This power supply is designed for API670 turbomachinery protection systems and meets SIL2 requirements for rotating equipment safety monitoring.

 

Technical Specifications

 

Item Parameter
Brand Vibro-Meter (Meggitt / Baker Hughes)
Model RPS6U, Part No. 200-582-500
Module Type 6U Rack Power Supply
Input Voltage AC version: 90–264 VAC, 47–63Hz; DC variants: 24VDC / 110VDC options
Output Rails +5VDC @ 35A; +12VDC @ 6A; -12VDC @ 2A
Rated Power 300W continuous
Ripple ≤50mVpp (20MHz bandwidth)
Protection Overvoltage, overcurrent, short-circuit, overtemperature
Redundancy Dual unit parallel hot redundant configuration
Hot Swap Supported under redundant rack condition
Operating Temperature -25°C ~ +65°C
Storage Temperature -40°C ~ +85°C
Humidity 5%–95% non-condensing
Vibration IEC 60068-2-6
Shock IEC 60068-2-27
Form Factor 6U, 12TE front card for ABE04x rack
Weight Approx. 2.1kg
Enclosure Rating IP20 when rack mounted
Certifications CE, SIL2 compatible, API 670 compliant
Diagnostics Input loss, output under/over voltage, over temperature, fan fault

 

Compatibility & Installation Pitfalls

Compatibility

  • Host Rack: ABE041 / ABE042 6U rack
  • Compatible Modules: CPUM, MPC4, IOC4T, IOC16T, IRC4, AMC8
  • Configuration Software: RPS / MPS engineering software
  • Redundancy: Two RPS6U modules in same rack for N+1 redundant power
  • Not compatible: Generic VME racks, Bently 3500 racks, non- backplanes

Critical Installation Pitfalls

  1. Input variant matching: Confirm AC / DC input version before applying power. Wrong input voltage will permanently damage the .
  2. Redundancy hot swap prerequisite: Hot swap can only be performed when the second is fully healthy and carrying rack load. Do NOT hot swap if only one power supply remains operational.
  3. Backplane connector integrity: The connects to backplane with dual rear connectors. Bent or dirty pins cause intermittent power drops and random module resets. Do not force insertion.
  4. Derating at high temperature: Output power derates 1% per °C above 60°C. Poor cabinet ventilation leads to thermal derating and unexpected shutdown.
  5. Load calculation: Sum total power consumption of all cards before commissioning. Overloading exceeds current limit and triggers protection shutdown.
  6. Ground bonding: Protective earth must be securely connected to rack chassis. Poor grounding introduces noise into backplane power and false power fault alarms.
  7. Fan dust accumulation: Internal cooling fan requires periodic inspection. Dust clogging causes over-temperature trips and premature failure.

 

Standard Operating Procedure (SOP)

  1. Pre-Install Inspection & LOTO Lock-out tag-out rack input power. Inspect for physical damage, fan blockage or connector corrosion. Confirm part number and input variant match system BOM.
  2. Module Insertion Insert into dedicated power slot on ABE04x rack. Push fully home to engage rear backplane connectors. Secure front panel fasteners. Install second if redundant power is required.
  3. Input Power Wiring Connect AC/DC input source to the terminal block. Fit input fuses/circuit breaker. Torque terminals and connect protective earth.
  4. Open RPS software, add to hardware configuration, enable power supply diagnostic alarm reporting. Download configuration to CPUM.
  5. Power-Up & Commissioning Restore input power. Check front panel LED status for all power rails. Verify voltage readings via RPS software. Test redundant failover by simulating loss of one .
  6. Runtime Operation & Diagnostics Continuously monitor rail voltages, temperature and fault logs through HMI or RPS software. Clean fan assembly during scheduled outages.
  7. Hot-Swap Replacement Procedure Confirm the second redundant is healthy. Release front panel fasteners and pull faulty unit out. Insert spare , seat fully. Verify LED status and diagnostic readings after replacement. No full rack configuration download required.

 

Application Scenarios

  • Steam & Gas Turbine Machinery Protection (API670)
  • Centrifugal Compressor Vibration & Shaft Monitoring
  • Generator condition monitoring systems
  • Petrochemical turbomachinery safety racks
  • Power plant critical rotating equipment protection
  • Offshore platform machinery monitoring cabinets
  • system spare replacement and retrofit projects

 

Supporting Components

  1. ABE04x 6U Rack
  2. CPUM 200-595-100-01 CPU module
  3. MPC4 Vibration protection module
  4. IOC4T Rear communication node card
  5. IOC16T Analog input module
  6. IRC4 Relay trip output module
  7. RPS / MPS configuration software
  8. Input circuit breakers and fuses
  9. Shielded power cables
  10. Blank filler panels for unused rack slots

 

Related Model Recommendations (10 Models)

  1. CPUM 200-595-100-01: rack CPU
  2. MPC4 200-510-071-113: Vibration protection card
  3. IOC4T 200-560-000-113: Rear I/O communication card
  4. IOC16T 200-565-000-013: 16-channel analog input
  5. IRC4: Relay trip output module
  6. AMC8: Analog measurement module
  7. GSI127 244-127-000-017-A2-B: Galvanic separation unit
  8. XMV16: High density condition monitoring module
  9. IQS9xx: Eddy current signal conditioner
  10. CA-series IEPE accelerometer