Valmet (Metso) A413000 Processor Module

  1. A413001: Valmet series power supply module
  2. A413004: Gate interface module for rack
  3. A413005: Analog input module
  4. A413045: Analog output module
  5. A413188: Digital I/O module
  6. A413330: Rack power unit
  7. A413010: Serial communication interface board
  8. A413020: Digital input module
  9. A413025: Digital output module
  10. A413030: Signal conditioning module
Category: SKU: VALMET Brand:

Description

Valmet (Metso) A413000 Processor Module

 

Product Title

Valmet (Metso) A413000 | 32-bit RISC CPU Processor Module for Valmet DCS A413000 Series

 

Product Description

The Valmet A413000 (originally Metso) is a plug-in 32-bit RISC processor module serving as the main controller for Valmet legacy distributed control system, widely used in pulp & paper mill automation. It executes real-time control logic, data acquisition, alarm management and communication with local I/O modules and upper SCADA host. Equipped with onboard RAM and flash memory, it stores control programs and historical process data. Dual serial ports support communication with field I/O boards and operator stations. Built-in hardware watchdog provides fail-safe protection upon processor crash. Continuous self-diagnostics monitor internal memory, bus communication and power status, reporting fault alarms to the DCS system. This legacy controller is commonly used for spare part replacement and system retrofit for existing paper, power and chemical plants.

 

Technical Specifications

 

Item Parameter
Brand Valmet (Former Metso Automation)
Model A413000
Module Type DCS Main Processor CPU Module
CPU Core 32-bit RISC Processor
Onboard RAM 256 KB
Flash Memory 512 KB
Communication Ports 2 × Serial port (RS232/RS485)
Onboard Function Hardware Watchdog Timer, Self-diagnostic
Supply Voltage 24 VDC ±10%
Power Consumption Max 6 W
Operating Temperature -20°C ~ +60°C
Storage Temperature -40°C ~ +80°C
Humidity 5%–95% non-condensing
MTBF 50,000 hours
Form Factor Standard rack plug-in module
Enclosure Rating IP20 when rack mounted
Supported I/O Full A41300 series I/O modules
Certification CE

 

Compatibility & Installation Pitfalls

Compatibility

  • System Platform: Valmet / Metso A41300 series DCS rack system
  • Matching I/O Modules: A413001, A413004, A413005 and other A413xx series
  • Configuration Software: Valmet DCS engineering tool
  • Backplane: Dedicated A41300 series rack backplane
  • Not compatible: Third-party generic VME racks, modern Valmet DNA system

Critical Installation Traps

  1. Firmware revision matching: The A413000 firmware must match existing rack and I/O firmware. Mismatched firmware leads to bus communication failure and program download failure.
  2. No hot swap: This CPU module does NOT support hot swapping. Full LOTO and complete rack power-down required before removal or installation.
  3. Backplane pin damage: Edge connector pins are fragile. Never force insertion. Bent pins result in intermittent communication loss or total CPU offline.
  4. ESD sensitive circuit: PCB memory and processor chips are ESD sensitive. Wear anti-static wristband; avoid touching gold edge connectors.
  5. Rack ventilation requirement: Poor cabinet airflow causes overheating, watchdog reset and unexpected CPU crash. Keep rack ventilation unblocked.
  6. Ground loop interference: Serial communication cables must use shielded twisted pair with single-point grounding. Multiple grounding points create ground loops and unstable data transmission.
  7. Memory corruption risk: Power surge during download can damage onboard flash. Always stabilize 24VDC power before program downloading.

 

Standard Operating Procedure (SOP)

  1. Pre-Installation Inspection & LOTO Perform lock-out tag-out and fully de-energize DCS rack. Inspect for PCB damage, connector corrosion. Verify firmware revision matches existing system BOM. Prepare ESD protection kit.
  2. Module Insertion Align module with designated CPU slot on Valmet A41300 rack. Push steadily until fully seated into backplane, secure front panel fasteners.
  3. Communication Wiring Connect serial bus cables between CPU and I/O modules. Use shielded twisted pair cable. Complete continuity and insulation resistance test.
  4. Software Configuration & Program Download Launch Valmet DCS engineering software. Confirm hardware configuration, compile control logic, download program into flash memory.
  5. Power-Up & Commissioning Restore rack power. Wait for CPU boot and self-test. Check front LED indicators. Verify I/O communication, control logic execution and watchdog fault response.
  6. Continuous Operation & Diagnostics Monitor CPU status, memory health and diagnostic alarms via DCS HMI. Back up control program periodically.
  7. Replacement Procedure Execute LOTO and power off rack. Disconnect serial cables. Remove front fasteners and extract faulty . Install spare CPU, download control program, re-commission and validate all control loops.

 

Application Scenarios

  • Pulp and Paper Mill DCS process control
  • Power plant auxiliary boiler control systems
  • Chemical plant continuous process monitoring
  • Wastewater treatment automation
  • Paper machine quality control & interlock
  • Legacy Metso DCS system retrofit & spare replacement
  • Mining process control systems

 

Supporting Components

  1. Valmet A41300 series DCS Rack
  2. A41300 dedicated backplane
  3. A4130xx I/O modules
  4. Valmet DCS engineering configuration software
  5. 24VDC regulated rack power supply
  6. Shielded RS485 serial communication cable
  7. Anti-static wristband and ESD mat
  8. Digital multimeter
  9. Program backup storage media
  10. Rack blank filler panels

 

Related Model Recommendations (10 Models)

  1. A413001: Valmet series power supply module
  2. A413004: Gate interface module for rack
  3. A413005: Analog input module
  4. A413045: Analog output module
  5. A413188: Digital I/O module
  6. A413330: Rack power unit
  7. A413010: Serial communication interface board
  8. A413020: Digital input module
  9. A413025: Digital output module
  10. A413030: Signal conditioning module