Description
SIEMENS MOORE 16407-1-1 — APACS+ MODULRAC Chassis Rack Backplane, 10-Slot I/O Interconnect Board Assembly

16407-1-1
Brand & Model Title
Siemens Moore (Moore Products Co. heritage) 16407-1-1 — APACS+ MODULRAC Backplane Assembly, 10-Slot I/O Chassis Interconnect Board (the Module Bus / “MBUS board” inside the rack)
The 16407-1-1 is a backplane PCB assembly — not a module, not a card that goes in a slot, and not an I/O interface. It is the board that sits at the bottom of an APACS+ MODULRAC 10-slot chassis, into which every I/O module plugs from the front, and on which the Module Bus, module power distribution and the rear field-connector field all terminate. Moore’s own assembly designation is the giveaway: “ASSY 16407-1-1 — CHASSIS RACK BACKPLANE” . In APACS+ field language this is the M-Bus board of the rack.
That identity is practically important, because it means the part is what comes out when a rack is torn down. Weidmüller’s published APACS migration procedure begins: “Remove all parts from Modulrac (I/O module, metal frame and MBUS Board) leaving only I/O connectors” — the MBUS board being removed there is this assembly.
Main Technical Specifications
| Parameter | Value (verified) / (reported) |
|---|---|
| Product type | Passive backplane / chassis interconnect PCB assembly |
| Moore designation | ASSY 16407-1-1, CHASSIS RACK BACKPLANE |
| System | Moore APACS+ / QUADLOG I/O chassis (MODULRAC) |
| Slot capacity | 10 slots (matches the 16114-xxx 10-slot MODULRAC chassis) |
| Function | Mechanical location and electrical interconnect for I/O modules; carries the Module Bus and slot power; terminates at the rear field-connector field |
| Bus | APACS+ Module Bus (M-Bus), chassis-internal |
| Weight | ≈ 0.52 kg (supplier-listed) |
| Mounting | Integral to the rack; not DIN-rail, not hot-swappable |
| Lifecycle | Discontinued — surplus / refurbished only |
| Asking prices observed | Wildly inconsistent (hundreds to ~USD 5,000) — treat high asks as channel noise, not value |
Typical Applications
- Rack rebuild / chassis restoration — the part you replace when a MODULRAC has been damaged by corrosion, coolant or water ingress, or when a rack is being re-populated from spares
- Chassis transplant — moving a working set of I/O modules into a sound chassis when the original backplane is beyond cleaning
- Intermittent module faults that follow the slot — the diagnostic signature of a worn or contaminated backplane connector rather than a failing module
- Field-connector repair — the rear termination field is part of this assembly, so crushed or corroded rear connectors are a backplane-level repair
- Migration teardown — removal ahead of a Weidmüller adapter-rack conversion, where the I/O connectors stay and the MBUS board comes out
- Spares holding for legacy refining, petrochemical, power and pulp & paper APACS+ sites
Related News & Events
- Three different products are being sold under this one number. It appears as an “APACS+/QUADLOG I/O Module Interface” with galvanic isolation, FM Class I Div 2 approval and per-channel diagnostics; as a “High-Speed Digital Processing Module, 16-bit @ 50 MHz, 16 DI/16 DO, IP65” ; and as a “Module Backplane with 16 slots, 35 mm DIN-rail mounting, hot-swap and a SIL 3 safety bus” . A backplane is none of these: it has no processor, no channels, no enclosure and no DIN clip, and it cannot hot-swap itself. The fabrication is unusually blatant here — one page even invents a “zero-downtime case study” around it.
- “16407-1-1” versus “16407-01-1”. Both forms circulate. Moore’s assembly format is 16407-1-1 (the extra zero is a transcription artefact seen across the whole Moore range, e.g. 16147-51-2 / -02). They are almost certainly the same assembly, but the printed label on the board is the only authority — confirm before paying a premium for what a seller calls a “different variant”.
- Slot count conflicts. One listing says 16 slots, another says 8–16 “depending on configuration”. The 10-slot figure matches the 16114-xxx 10-slot MODULRAC chassis that this board belongs to, and is the only number tied to an actual chassis part number. Count the slots in your rack, not on a web page.
- Passive hardware, mechanical failures. Almost every real 16407-1-1 fault is a contact problem, not an electronic one: bent or recessed pins in the module connectors, oxide films, cracked solder fillets where the edge connectors are staked to the PCB, and corrosion in coastal or sour-service plants. Clean and inspect before condemning; replace only when pins are deformed or the board is delaminating.
- It is not a hot-swap item. Removing a backplane means de-energising the rack, unplugging every module, and disturbing the field terminations at the rear. Plan it as an outage task with a full wiring schedule and photographs taken before anything is unplugged — the rear connector field is not something to reconstruct from memory.
- Pricing signal: the same part is listed at a few hundred dollars by PCB brokers and at ~USD 5,000 by DCS “specialists” with a 99999-style strike-through price. For a passive 10-slot backplane, the former is the realistic order of magnitude. Insist on photographs of the actual board and its label.
- Lifecycle: APACS+ / QUADLOG is fully discontinued. QUADlog was also licensed into Yokogawa ProSafe-PLC, so expect occasional cross-labelling. Forward paths are Siemens PCS 7 migration or the Weidmüller adapter rack, which reuses existing field terminations.
Related Product Recommendations
| Model | Description |
|---|---|
| 16114-1-04 / 16114-1-06 | MODULRAC 10-slot rack chassis, 24 V — the chassis this backplane belongs to |
| 16114-171 / 16114-500 | MODULRAC rack variants (verify slot count and rear connector style) |
| 16168-1-1 | PSM (Power Supply Module) Transition Board |
| 16147-51-02 / 16147-21-2 | ACM Transition Boards |
| 16140-1 / 16140-1-1 | SAM termination strip |
| 16169-1-1 … 16169-1-7 | SAM marshalled termination assemblies |
| 16167-1-1 … 16167-1-8 | SDM marshalled termination assemblies |
| 39SAMCAN / 39EAMCBN / 39ODM115ACCAN | Standard analog, enhanced analog and discrete output modules that plug into this backplane |
| QLSDM024DCCBN / QLSAMBAN / QLCCM24AAN | QUADLOG discrete, analog and CCM modules |
| 16137-222 / 223, 16137-151 / 153 | M-Bus “A”/”B” cables, 2.5 m and 4 m |
| 16137-173 / 16137-176 | M-Bus “A”/”B” termination plugs |
| 16137-60 | 24 V power cable, unterminated |
| Weidmüller APACS adapter rack | Field-termination-preserving migration hardware |
| Siemens PCS 7 | Documented migration target |


