Bently Nevada 133292-01, 3500/15 Low Voltage DC Power Supply Module, Baker Hughes 3500 Mechanical Protection TSI System Rack Power Supply

  1. 127610-01 (3500/15 AC power supply)
  2. 133300-01 (Low Voltage DC PIM Input Module, match 133292-01)
  3. 3500/42 Proximitor Displacement Monitor
  4. 3500/40 Gap / Vibration Monitor
  5. 3500/50 Keyphasor Module
  6. 3500/32 Relay Module
  7. 3500/22 TDI Transient Data Interface
  8. 3500/20 RIM Rack Interface Module
Category: SKU: BENTLY NEVADA 133292-01 3500/15 Brand:

Description

Bently Nevada 133292-01, 3500/15 Low Voltage DC Power Supply Module, Baker Hughes 3500 Mechanical Protection TSI System Rack Power Supply

 

Product Overview

133292-01 belongs to the Bently Nevada 3500/15 series, a low-voltage DC-DC power module that supplies power to the entire 3500 TSI unit vibration monitoring and protection rack. The module receives external 24VDC input, converts it into multiple stabilized DC channels, and supplies power to all sub cards such as vibration monitoring, displacement, speed, relays, and communication to the rack backplane. The rack supports dual power redundant hot backup, with two power supplies, one primary and one backup; Under redundant configuration, it supports hot swapping, and unplugging one of them will not interrupt the operation of the entire TSI system. Supporting PIM input module: 133300-01 (low-voltage DC input interface module). The original factory has ceased production, and only new inventory or refurbished spare parts are used for the replacement of TSI systems for power plant steam/gas turbines.

350015 133292-01

Key Technical Specifications

  • Part Number: 133292-01
  • Manufacturer: Bently Nevada (Baker Hughes, USA)
  • Model: 3500/15 Low Voltage DC Power Supply
  • Input: 20~30VDC (Nominal 24VDC)
  • Rack Position: Half-height module, must install on the dedicated left slots of 3500 rack
  • Redundancy: Dual redundant hot standby supported
  • Protection: Overvoltage, undervoltage, short-circuit protection
  • Indicator: Front panel “Supply OK” LED status
  • Operating Temperature: -20°C ~ +70°C
  • Storage Temperature: -40°C ~ +85°C
  • Humidity: 5%~95% non-condensing
  • Isolation: 1500VDC input to output isolation
  • Weight: ~1.2~1.4kg

 

Recommended 8 Similar Models (3500 TSI series)

  1. 127610-01 (3500/15 AC power supply)
  2. 133300-01 (Low Voltage DC PIM Input Module, match 133292-01)
  3. 3500/42 Proximitor Displacement Monitor
  4. 3500/40 Gap / Vibration Monitor
  5. 3500/50 Keyphasor Module
  6. 3500/32 Relay Module
  7. 3500/22 TDI Transient Data Interface
  8. 3500/20 RIM Rack Interface Module

 

Quality Control & Test SOP

  1. Visual Inspection: Check PCB, capacitors, front panel, edge connector and label, confirm PN 133292-01, check burnt marks, swollen capacitors or bent gold fingers.
  2. Continuity Test: Check backplane edge pins, power tracks for open/short circuit.
  3. Insulation Resistance Test: Input to output isolation test.
  4. Power-Up Functional Test: Install on 3500 rack with 133300-01 PIM, apply 24VDC input, verify “Supply OK” LED, stable output without overheating.
  5. Load Test: Apply simulated full rack load, test output voltage stability and ripple.
  6. Protection Test: Simulate overvoltage/short circuit to verify protection trigger.
  7. Redundancy Switchover Test (if two power supplies fitted): Test auto switchover between primary and standby.
  8. Environmental Burn-in Test: Powered burn-in for early failure screening.
  9. Final Recheck & Documentation: Repeat load test, generate serial-number traceable test report before anti-static packaging.

350015 133292-01

Installation Guide

  1. Pre-Install Preparation: Perform LOTO lockout-tagout for TSI cabinet, wear ESD wrist strap. Confirm matched PIM 133300-01.
  2. Rack Slot Inspection: Inspect left-side rack backplane connector for oxidation or damage.
  3. Module Insertion: Insert 133292-01 into the dedicated half-height left slot, lock the front latch.
  4. Wiring: 24VDC field power wiring to 133300-01 PIM terminal, follow Bently grounding rules.
  5. Power Restore: Energize 24VDC input, observe front panel “Supply OK” LED.
  6. Commissioning: Enter 3500 configuration software, read power supply health status via RIM/TDI, verify all rack monitoring modules power up normally.
  7. Redundancy Test (dual power): Manually cut primary power to confirm seamless switchover to standby unit, no TSI trip.
  8. Post-Install Documentation: Record serial number, measured voltage, commissioning log into turbine asset spare records.

 

Application Scenarios & Features

Application Scenarios

  • Thermal power plant steam / gas turbine TSI machinery protection system
  • Compressor, large rotating machinery vibration, shaft displacement, speed monitoring
  • Spare replacement for failed 3500/15 DC power supply in existing Bently 3500 racks

Core Features

  • Dedicated low voltage DC power supply for Bently Nevada 3500 TSI rack
  • Supports dual redundant hot standby configuration for high availability turbine protection
  • Hot-swap capable (only when redundant second power supply remains online)
  • Built-in multiple protections: overvoltage, undervoltage, short-circuit
  • Front panel LED for quick health status diagnosis
  • Half-height plug-in design for standard 3500 rack
  • US original Bently Nevada hardware for turbomachinery protection

 

FAQ

Q1: What is difference between 133292-01 and 133300-01?

A1: 133292-01 = DC power supply module (power conversion card), plugs into rack. 133300-01 = PIM Power Input Module, external 24VDC terminal interface, mounted at rack rear, works together with 133292-01.

Q2: Can 133292-01 hot swap?

A2: Only redundant dual power configuration supports hot swap. Single power setup: removing it will cut off entire rack power, TSI protection will lose power and trip.

Q3: Is 133292-01 SIL certified?

A3: The power module itself does not carry standalone SIL certification. SIL assessment is done for the full 3500 machinery protection system.

Q4: Common failures of 133292-01?

A4: Electrolytic capacitor aging / bulging (most common), output voltage drift, overvoltage protection lockup, gold finger oxidation.

Q5: Is 133292-01 discontinued?

A5: Yes, Bently stopped new production. Only surplus new or refurbished spare stock available.

Q6: Difference between AC 3500/15 and 133292-01 DC version?

A6: AC version (127610-01) uses 85~264VAC mains input. 133292-01 accepts 24VDC field DC power supply.

Q7: Which rack slot does it occupy?

A7: Half-height module, must be fitted on the left side dedicated power slots of 3500 rack, cannot use regular monitor card slots.

Q8: What happens if this power supply fails in redundant rack?

A8: The standby power supply automatically takes over, the TSI monitoring and protection logic continues running without interruption.