ABB PM860K01 (3BSE018110R1) AC 800M Processor Unit Kit for System 800xA DCS

  1. ABB PM861AK01 3BSE018157R1
  2. ABB PM862K02 3BSE081636R1
  3. ABB PM863K01 3BSE088381R1
  4. ABB PM864AK01 3BSE018161R1
  5. ABB PM866AK01 3BSE076939R1
  6. ABB CI854BK01 PROFIBUS Communication Interface
  7. ABB S800 I/O TU810 Termination Unit
  8. ABB SD821 Power Supply Unit
Category: SKU: ABB PM860K01 3BSE018110R1 Brand:

Description

ABB PM860K01 (3BSE018110R1) AC 800M Processor Unit Kit for System 800xA DCS

 

Product Overview

The ABB PM860K01 (3BSE018110R1) is a 32-bit processor unit kit belonging to the ABB AC 800M controller family for System 800xA distributed control system. This complete kit contains PM860 CPU module, TP830 baseplate, CEX-bus terminator TB850, ModuleBus terminator TB807 and memory backup battery. It executes real-time control logic, handles process data acquisition, alarm management and interlock calculation, and communicates with S800 I/O modules via ModuleBus and CEX bus. It supports dual Ethernet ports for plant network communication and multiple fieldbus interfaces to connect field instruments, drives and third-party systems. This legacy controller is phased out of active production by ABB and is mainly supplied as spare replacement for existing System 800xA installations in power, pulp & paper and petrochemical plants.

ABB PM860K01 3BSE018110R1

Key Technical Specifications

  • Part Number: PM860K01, 3BSE018110R1
  • Manufacturer: ABB
  • Series: AC800M, System 800xA DCS
  • Processor: 32-bit single-board CPU
  • Memory: 16MB RAM, onboard flash for application program storage
  • Backup: Lithium battery for retention of RAM variables during power loss
  • Communication Interfaces
    • Dual 10/100 Mbps Ethernet (Modbus TCP, OPC, CNCP time sync)
    • ModuleBus for S800 I/O
    • CEX bus for up to 12 CEX communication modules
    • Supports PROFIBUS DP, FOUNDATION Fieldbus via CI-series communication modules
  • Power Supply: 24VDC (19.2~30VDC)
  • Power Consumption: Approx. 1.2W
  • Operating Temperature: +5°C ~ +55°C
  • Storage Temperature: -40°C ~ +70°C
  • Relative Humidity: 5%~95%, non-condensing
  • Protection Class: IP20 (for cabinet installation)
  • Mounting: DIN rail mount
  • Weight: ~1.1 kg
  • Diagnostics: Built-in watchdog, program execution monitoring, bus fault detection, front panel LED status indicators
  • Compliance: CE, UL508; SIL capable only with full system assessment (not standalone SIL certified)

 

Recommended 8 Similar Series Models (AC800M / System800xA)

  1. ABB PM861AK01 3BSE018157R1
  2. ABB PM862K02 3BSE081636R1
  3. ABB PM863K01 3BSE088381R1
  4. ABB PM864AK01 3BSE018161R1
  5. ABB PM866AK01 3BSE076939R1
  6. ABB CI854BK01 PROFIBUS Communication Interface
  7. ABB S800 I/O TU810 Termination Unit
  8. ABB SD821 Power Supply Unit

 

Quality Control & Test Standard Operating Procedure (SOP)

  1. Visual Inspection: Inspect CPU PCB, baseplate, connectors, front panel LEDs, battery and labels. Confirm part number and revision match documentation; check for scratches, corrosion or damaged pins.
  2. Continuity & Insulation Test: Perform pin continuity check on ModuleBus, CEX bus and power terminals; insulation resistance test between 24VDC power and signal circuits.
  3. Power-Up Test: Apply 24VDC power gradually. Verify power consumption within rated range, LED boot sequence completes normally, no overheating.
  4. Built-in Self-Diagnostic Test: Execute controller self-test, verify watchdog function, memory integrity, battery voltage check and internal fault detection.
  5. Application Program Load & Execution Test: Download test control program. Validate program scan cycle, logic execution, analogue and digital variable handling.
  6. Bus Communication Test: Connect S800 I/O and CEX communication modules. Verify stable ModuleBus and CEX bus data exchange.
  7. Ethernet & Fieldbus Interface Test: Validate dual Ethernet port communication, Modbus TCP read/write and time synchronization. Test CEX fieldbus interface signal transmission.
  8. Power Loss Retention Test: Cut off 24VDC supply and restore power. Confirm variable data is retained by backup battery.
  9. Environmental Burn-in Test: Continuous powered burn-in under rated ambient temperature for screening early-life component failures.
  10. Final Recheck & Documentation: Repeat core functional tests after burn-in. Generate serial-number traceable test report before anti-static packaging.

 

New Module Installation Guide

  1. Pre-Install Preparation: Perform LOTO procedure for DCS cabinet. Wear ESD wrist strap and anti-static mat. Confirm PM860K01 kit part number matches site BOM and System800xA software compatibility.
  2. DIN Rail Preparation: Inspect DIN rail inside control cabinet, ensure rail is clean and firmly mounted.
  3. Baseplate & CPU Mounting: Clip TP830 baseplate onto DIN rail, then mount PM860 CPU onto the baseplate. Install TB850 CEX-bus terminator and TB807 ModuleBus terminator at bus end positions. Install backup battery following polarity instructions.
  4. Bus & Power Wiring: Wire 24VDC power supply, ModuleBus cable, CEX bus cable and Ethernet cables. Follow System800xA wiring manual, implement proper cable shielding and single-point grounding.
  5. Power Restore: Energize 24VDC control power. Observe front panel LEDs, wait for controller boot-up and bus initialization.
  6. Commissioning & Programming: Connect Control Builder M engineering tool, download valid application program and system configuration. Assign network IP addresses, configure fieldbus parameters and I/O mapping.
  7. I/O & Logic Simulation Test: Simulate analogue and digital I/O signals, verify control logic, alarm generation and interlock action. Check data transmission to 800xA HMI.
  8. Post-Installation Record: Back up application program, record serial numbers and commissioning test results into plant DCS maintenance log.

ABB PM860K01 3BSE018110R1

Application Scenarios & Features

Application Scenarios

  • Thermal power plant boiler, turbine and auxiliary system DCS control
  • Petrochemical, refinery and LNG plant process control
  • Pulp & paper, mining and water treatment industrial automation
  • Combined-cycle power generation System800xA distributed control systems
  • Retrofit and spare replacement for legacy AC800M controller cabinets

Core Features

  • 32-bit high-performance CPU for real-time sequential, regulatory and interlock control
  • Complete processor kit including baseplate, bus terminators and backup battery
  • Dual independent Ethernet ports for redundant plant network communication
  • Flexible expansion via CEX bus to support multiple fieldbus types
  • ModuleBus interface for S800 series remote I/O system
  • Onboard backup battery retains process variables upon power failure
  • Comprehensive hardware diagnostics and watchdog protection
  • Native integration within ABB System 800xA DCS ecosystem

 

FAQ

Q1: What does PM860K01 kit contain?

A1: The kit includes PM860 CPU, TP830 baseplate, TB850 CEX-bus terminator, TB807 ModuleBus terminator and memory backup lithium battery.

Q2: Is PM860K01 redundant?

A2: supports simplex configuration only. For redundant controller pair, select PM861 or PM866 series AC800M processors.

Q3: Can I hot-swap PM860 CPU?

A3: The CPU module can be hot-plugged onto TP830 baseplate. However, removing the active running controller will stop control execution and interrupt I/O processing. Hot swap is not allowed during critical plant operating states.

Q4: Is SIL certified?

A4: SIL certification applies to the whole safety function including controller, I/O, program and field devices. The standalone controller is not SIL certified. Use PM863 for SIL3 safety applications.

Q5: What happens when backup battery fails?

A5: After power loss, RAM variables will be lost. The controller will load the application program from flash, but runtime parameters will reset. Replace battery periodically as per maintenance schedule.

Q6: What is the maximum CEX bus modules supported?

A6: PM860 supports up to 12 single CEX bus communication modules.

Q7: What engineering software is used for ?

A7: ABB Control Builder M for programming, configuration, download and online monitoring. It works together with System 800xA HMI.

Q8: Is still in production?

A8: ABB has discontinued PM860 series. New projects use newer AC800M controllers, is available as spare replacement only.